visable.png

Skip header
 

Edit

This section describes the user tools in the Edit menu under Copier / Document Server Features.

Default settings are shown in bold type.

Enter the width of the binding margin with the number keys as follows:

Enter the width of the erased margin with the number keys as follows:

An image of approximately 1.5 mm (0.06 inch) will not be displayed as the width of the separation line, when specifying solid or broken lines.

Front Margin: Left / Right

Specify left and right margins on the front side of copies in Margin Adjustment mode.

The default setting is Left, 5 mm (Metric version) / Left, 0.2 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Settings made on the main machine are applied.

Back Margin: Left / Right

Specify left and right margins on the back side of copies in Margin Adjustment mode.

The default setting is Right, 5 mm (Metric version) / Right, 0.2 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Settings made on the main machine are applied.

Front Margin: Top / Bottom

Specify top and bottom margins on the front side of copies in Margin Adjustment mode.

The default setting is T/B: 0 mm (Metric version) / T/B: 0.0 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Settings made on the main machine are applied.

Back Margin: Top / Bottom

Specify top and bottom margins on the back side of copies in Margin Adjustment mode.

The default setting is T / B: 0 mm (Metric version) / T / B: 0.0 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Settings made on the main machine are applied.

1 Sided 2 Sided Auto Margin: TtoT

In 1 sided to 2 sided Duplex mode, you can specify the margins on the back side.

The margin is set to the same value of “Back Margin: Left/Right”.

The default setting is Right, 5 mm (Metric version) / Right, 0.2 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Settings made on the main machine are applied.

1 Sided 2 Sided Auto Margin: TtoB

In 1 sided to 2 sided Duplex mode, you can specify the margins on the back side.

The value set for “Back Margin: Top/Bottom” is used.

The default setting is T / B: 0 mm (Metric version) / T / B: 0.0 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Settings made on the main machine are applied.

Erase Border Width

Specify the width for erasing border.

The default setting is 10 mm (Metric version) / 0.4 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Settings made on the main machine are applied.

Erase Original Shadow in Combine

In Combine mode, you can specify whether to erase a 3 mm, 0.1 inch boundary margin around all four edges of each original.

The default setting is On.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Erase Center Width

Specify the width of the erased center margins with this function.

The default setting is 10 mm (Metric version) / 0.4 inch (Inch version).

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Front Cover Copy in Combine

You can make a combined copy on the front cover sheet when you select Front Cover mode.

Illustration of Front Cover Copy in Combine

The default setting is Combine.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Copy Order in Combine

You can set the copy order in Combine mode.

Illustration of Copy Order in Combine

The default setting is From Left to Right.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Orientation: Booklet, Magazine

Select the opening orientation of copies made using Booklet or Magazine mode.

The default setting is Open to Left.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Copy on Designating Page in Combine

Specify whether to make a combined copy on the inserted slip sheets in Desig./Chapter mode.

The default setting is Combine.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Image Repeat Separation Line

You can select a separation line using the Image Repeat function from: None, Solid, Broken A, Broken B, or Crop Marks.

  • None

    Illustration of Image Repeat Separation Line

  • Solid

    Illustration of Image Repeat Separation Line

  • Broken A

    Illustration of Image Repeat Separation Line

  • Broken B

    Illustration of Image Repeat Separation Line

  • Crop Marks

    Illustration of Image Repeat Separation Line

The default setting is None.

Selecting solid or broken lines might produce a blank area of approximately 1.5 mm (0.06 inch) in width along the separation line.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Double Copies Separation Line

You can select a separation line using the Double Copies function from: None, Solid, Broken A, Broken B, or Crop Marks.

  • None

    Illustration of Double Copies Separation Line

  • Solid

    Illustration of Double Copies Separation Line

  • Broken A

    Illustration of Double Copies Separation Line

  • Broken B

    Illustration of Double Copies Separation Line

  • Crop Marks

    Illustration of Double Copies Separation Line

The default setting is None.

Selecting solid or broken lines might produce a blank area of approximately 1.5 mm (0.06 inch) in width along the separation line.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Separation Line in Combine

You can select a separation line using the Combine function from: None, Solid, Broken A, Broken B, or Crop Marks.

  • None

    Illustration of Separation Line in Combine

  • Solid

    Illustration of Separation Line in Combine

  • Broken A

    Illustration of Separation Line in Combine

  • Broken B

    Illustration of Separation Line in Combine

  • Crop Marks

    Illustration of Separation Line in Combine

The default setting is None.

Selecting solid or broken lines might produce a blank area of approximately 1.5 mm (0.06 inch) in width along the separation line.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Copy Back Cover

When one-sided copying the back cover, you can specify whether to have the back cover outside (outside page) or inside (inside page).

The default setting is Outside.

The main machine applies the settings that have been made on it. Sub-machines also apply the settings made on the main machine, regardless of the settings made on them.

Settings made on the main machine are applied.